Ever since my buddy Dave bought a 1967 Ford Pickup a few months back, I've had the itch to buy something old, rough, and cool. I've been fighting the urge to pick up a 2nd 'project' for a few years, every spring I get depressed that it's been ~5 years since I had something cool to cruise. I also have zero knowledge of anything carburated or American made, and the best way to learn is to jump into a project.
Well this weekend I found what I was looking for on Craigslist. It wasn't a whole lot of money, not too far away, cool, old, unique, running and driving, and rough as fuck.
After a few text messages, I was convinced this was the truck I was looking for. So I borrowed a trailer, picked up my buddy Fro, and we set off on a 4 hour drive to Eastern West Virginia.
1962 Ford F-100 Unibody pickup. These unibody trucks were only produced for a few years, and I think they're really cool! It's a shortbed 2wd model with "three on the tree" manual trans and inline 6.
I think the badass keychain sealed the deal.
I bought it from a guy named Glen, who builds pretty sweet custom bikes. He had a few in his basement, this one was my favorite. I don't know a whole lot about bikes, but this is an old hardtail Triumph.
This thing was super clean! I was super impressed with the attention to detail and build quality. I don't know how this guy ended up with such a shitty old truck... but then again I bought it too, so I suppose we have a lot in common.
He also had this cafe style Suzuki on the lift under construction, and another Harley in the back.
After talking about bikes for a little too long, it was dark before we got to load up.
I waited until this morning to unload everything, it was freezing cold last night! But it was snowing today, which wasn't much better.
It has a sweet cherry bomb exhaust!
You can see the original color in the door jambs... possibly. It also may have been white, it's not really clear. If you look closely you can also see drywall screws, aluminum flashing, giant holes, silicone RTV, rust...
... and a FOOTPRINT GAS PEDAL. FUCK YEAH.
I found this mess of chicken wire, tape, foam, and bondo holding up part of the rear fender.
114 horsepower.
Fro, Woody, and I all fit!
Everybody keeps asking what my plans are... and I don't really have any. I need to get it legal first, then I will probably pursue the cheapest, fastest way to lower it to the ground. Right now I'm leaning toward a Crown Vic front clip with power steering, disc brakes, airride, and 20" Detroit Steel smoothies. I think I can make that happen without using much money or time.
Sunday, February 9, 2014
Some parts came in! It's been a while since I ordered actual parts, most of the supplies I buy are raw materials. This time I bought some Girling 60 dual piston calipers, Mintex pads, and 11" front rotors from a VW Corrado G60. It's a mild upgrade over stock, but the setup fills up large wheels a lot better.
Back to the heat shield. After the first several pieces weren't good enough, I tracked down a problem with my plywood hammerform. I bought a piece of solid red oak, and formed another piece.
After hammering:
I inked up the raw hammered part to smooth out the hammer marks using a selection of files and sandpaper.
Speaking of files... I bought a few new files for use in stainless steel. I really shouldn't be using files I use for regular steel, because steel particles can contaminate the surface of the stainless and cause it to rust.
After hours of hammering and filing, I was finally happy with the shape and quality of the piece.
But after closer inspection, I realized another problem! Forming the flange warped the piece, so I was correcting it with a flat dolly and slapping spoon. I left the protective film on the surface of the stainless to prevent damage, but had trimmed it back because it can't withstand the cutting and hammering of the edge. It turns out the edge of the protective film has ghosted itself into the surface of the stainless! This piece is scrap now too. The 8th one will be fucking perfect.
Back to the heat shield. After the first several pieces weren't good enough, I tracked down a problem with my plywood hammerform. I bought a piece of solid red oak, and formed another piece.
After hammering:
I inked up the raw hammered part to smooth out the hammer marks using a selection of files and sandpaper.
Speaking of files... I bought a few new files for use in stainless steel. I really shouldn't be using files I use for regular steel, because steel particles can contaminate the surface of the stainless and cause it to rust.
After hours of hammering and filing, I was finally happy with the shape and quality of the piece.
But after closer inspection, I realized another problem! Forming the flange warped the piece, so I was correcting it with a flat dolly and slapping spoon. I left the protective film on the surface of the stainless to prevent damage, but had trimmed it back because it can't withstand the cutting and hammering of the edge. It turns out the edge of the protective film has ghosted itself into the surface of the stainless! This piece is scrap now too. The 8th one will be fucking perfect.
Sunday, February 2, 2014
I bought some more Fragola master cylinder adapters.
Double flares or Bubble flares?? The part number says bubble, the bag says otherwise lol.
I kept on bending up brake lines. This is the right front line bent up in aluminum for practice. I bent this one in 4 pieces, carefully measuring every bend before transferring the measurements to the stainless steel tubing.
Then I bent the real lines - 304 stainless steel.
I bent up the left front line and added some P-clamps.
All done. I still have to make the final bends in the wheel wells that will connect to the braided hoses and calipers, but I'm still waiting on some bulkhead fittings and my brake calipers.
While the motor was out, I decided to finish the firewall section of my heat shield.
I made this hammerform out of Birch plywood.
This piece also had a bead-rolled flange just before the bend. I decided I didn't like the look after fitting it up.
So I made another one.
... and it wasn't good enough, so I made another one.
After the 3rd hammerform and 4th stainless piece, I decided to rethink my method a little bit. The first two hammerforms (and 2 pieces) were flawed because the hammerform wasn't cut perfectly. The 3rd hammerform was perfect... but there were two voids in the plywood which created soft spots that couldn't support the hammer blows, which made the bend radius uneven and ruined the look. I was thinking it was just my hamering technique, until I inspected the plywood and found two spots that I could compress with my finger due to gaps in one of the plies. I didn't even pretend to try and photograph this. I bought a chunk of solid Red Oak and a Freud 1/8" radius roundover bit, so I have no excuses on the 4th hammerform and 5th piece!
Double flares or Bubble flares?? The part number says bubble, the bag says otherwise lol.
I kept on bending up brake lines. This is the right front line bent up in aluminum for practice. I bent this one in 4 pieces, carefully measuring every bend before transferring the measurements to the stainless steel tubing.
Then I bent the real lines - 304 stainless steel.
I bent up the left front line and added some P-clamps.
All done. I still have to make the final bends in the wheel wells that will connect to the braided hoses and calipers, but I'm still waiting on some bulkhead fittings and my brake calipers.
While the motor was out, I decided to finish the firewall section of my heat shield.
I made this hammerform out of Birch plywood.
This piece also had a bead-rolled flange just before the bend. I decided I didn't like the look after fitting it up.
So I made another one.
... and it wasn't good enough, so I made another one.
After the 3rd hammerform and 4th stainless piece, I decided to rethink my method a little bit. The first two hammerforms (and 2 pieces) were flawed because the hammerform wasn't cut perfectly. The 3rd hammerform was perfect... but there were two voids in the plywood which created soft spots that couldn't support the hammer blows, which made the bend radius uneven and ruined the look. I was thinking it was just my hamering technique, until I inspected the plywood and found two spots that I could compress with my finger due to gaps in one of the plies. I didn't even pretend to try and photograph this. I bought a chunk of solid Red Oak and a Freud 1/8" radius roundover bit, so I have no excuses on the 4th hammerform and 5th piece!
I haven't stopped working on the car, but I have been terrible about updating this. I finally straightened out some computer issues, I'm back in action.
Last weekend, I went to World of Wheels here in Pittsburgh. Here are some of my favorites.
This was my favorite vehicle of the show.
I couldn't snag a clean photo through the crowd, but these two cars were badass.
I snagged a photo of Jason's whip. Wrinkle red!
So I built my entire engine with either ARP stainless bolts OR lathe-turned hex head bolts. This guy built his hot rod suspension with lathe-turned ARP stainless bolts. One upped.
... and he won a Ridler award for it lol.
I also bought another hammer. This is one of the few I need to complete my colection. After this hammer, I really only need 1 more to consider my collection "complete." This hammer and the last one are both completely useless, I'm only pursuing them in an effort to have the complete set. They're still available new, but I can't justify new prices ($100 each) so I'm waiting for bargains to pop up on eBay.
This is a 1991 Snap-on BF631 shrinking hammer. I might use the chisel end, but not the shrinking face. It was a little rough, but still had the original handle. I can't complain for the price!
It cleaned up surprisingly well! The rust was just surface rust, I was able to remove it all with some WD40 and Scotch-Brite in about 10 minutes.
The chisel end was pretty rough, so I filed it straight.
The original handle was loose, but I was able to tap the wedge tight and save the original handle.
I think I can squeeze one more in there!
Last weekend, I went to World of Wheels here in Pittsburgh. Here are some of my favorites.
This was my favorite vehicle of the show.
I couldn't snag a clean photo through the crowd, but these two cars were badass.
I snagged a photo of Jason's whip. Wrinkle red!
So I built my entire engine with either ARP stainless bolts OR lathe-turned hex head bolts. This guy built his hot rod suspension with lathe-turned ARP stainless bolts. One upped.
... and he won a Ridler award for it lol.
I also bought another hammer. This is one of the few I need to complete my colection. After this hammer, I really only need 1 more to consider my collection "complete." This hammer and the last one are both completely useless, I'm only pursuing them in an effort to have the complete set. They're still available new, but I can't justify new prices ($100 each) so I'm waiting for bargains to pop up on eBay.
This is a 1991 Snap-on BF631 shrinking hammer. I might use the chisel end, but not the shrinking face. It was a little rough, but still had the original handle. I can't complain for the price!
It cleaned up surprisingly well! The rust was just surface rust, I was able to remove it all with some WD40 and Scotch-Brite in about 10 minutes.
The chisel end was pretty rough, so I filed it straight.
The original handle was loose, but I was able to tap the wedge tight and save the original handle.
I think I can squeeze one more in there!
Subscribe to:
Posts (Atom)


























































